Products for Concrete Essentials
Sika® Clean-10
An Acid based Concrete Cleaner.
Use
Sika® Clean-10 is used to remove hardened concrete and mortar from equipment, concrete mixers, ready-mix trucks and tools
Characteristics and Advantages
- As equipment cleaner;
- To extend the life cycle of equipments
- To maintain an clean-looking outfit
Color
Clear
Packaging
25 kg
Sika® Clean-20
An Acid based Concrete Cleaner with a faster ability to remove hardened concrete and mortar from equipment.
Use
Sika® Clean -20 is used to remove hardened concrete and mortar from equipment, concrete mixers, ready-mix trucks and tools
Characteristics and Advantages
- As equipment cleaner;
- To extend the life cycle of equipments
- To maintain an clean-looking outfit
Color
Clear
Packaging
5 kg
25 kg
Separol®
A ready to use chemical release agent based form oil to release concrete surface out of formwork.
Use
Form release agent for steel, plastic and wooden formwork. Facilitates removal and cleaning of shuttering. The use of Separol® extends the life cycle of the form work substantially
Characteristics and Advantages
- Ready for use and easy to apply
- Ensures fair faced concrete finish. Does not impair adhesion of subsequent renderings and coatings.
- No staining
- Can also be applied for formwork used in steam curing process, as well as on damp shutterings
Color
Brown
Packaging
25 litre
200 litre
Sika® Formoil C
A concentrated Emulsified blend of purified Mineral Oil and non-hazardous Chemicals Based Formwork Release Agent which must be diluted with water (5-9 times maximum) prior to use.
Use
Sika® FormOil C provides clean, easy stripping of formwork particular on to steel and timber formwork and suit to actual condition prior to apply on formwork.
Characteristics and Advantages
- Prevent adhesion of concrete to formwork will allow air to escape from the interface during concrete placing and vibration
- The release of air minimizes surface blemishes and blow holes resulting in a substantial reduction in remedial cost
- Non hazardous and non toxic
- Non staining
- Ensures high quality fair-faced concrete
- Minimizes cleaning of shutters before use
- Does not rust steel moulds or equipment
- Can be used for all types of moulds and shutter faces
- Suspension and sediment free
- Job site mix
- Cost effectiveness depends on suitable proportion
- Over coat panting
Color
Light Brown
Packaging
200 litre
Sika® Formoil E
A controlled blended combination of refined Mineral Oil and Emulsifying Formwork Release Agent which is ready- to- use or can be diluted with water (1 part) prior to use.
Use
Sika® FormOil E is suitable for use on all types of formwork. It is either ready to use in opened-air condition with better release performance or ditute with water in roof protecting area with smooth surface.
Characteristics and Advantages
- Ready to use or can be ds diluted with water prior to use
- The range of dilutions give easy release of formwork and high quality surface finishes to concrete
- It is suspension and sediment free, highly fluid liquid which can be used in very fine sprays without clogging the jets
- Very economic coverage rates can be obtained without difficulty
- Continued use gives progressively better results on timber formwork
- Provides a quick, positive release of formwork, reducing labour costs and damage to formwork and moulds
- It drastically reduces the incidence of blowholes, surface blemishes and staining
- All tools can be cleaned with water
- It is an effective rust inhibitor
Packaging
200 litre
Sika® Form Release Agent
An Emulsion Based Formwork Release Agent which is designed to provide easy release of formwork. There are 3 different products for this type; Form Release Agent WB1, Form Release Agent WB2, and Form Release Agent WMR1.
Use
Sika® Form Release Agent is suitable for use on all types of formwork.
Characteristics and Advantages
- The range of dilutions give easy release of formwork and high quality surface finishes to concrete
- It is suspension and sediment free, highly fluid liquid which can be used in very fine sprays without clogging the jets
- Very economic coverage rates can be obtained without difficulty
- Continued use gives progressively better results on timber formwork
- Provides a quick, positive release of formwork, reducing labour costs and damage to formwork and moulds
- It drastically reduces the incidence of blowholes, surface blemishes and staining
- All tools can be cleaned with water
- It is an effective rust inhibitor
Color
Milky White
Packaging
200 litre
Sika® BondBreaker W
A water repellent, wax based bond breaker material.
Use
Sika® BondBreaker W is used for "match-cast", "tilt-up" and "tilt-slab" constructions.
Characteristics and Advantages
- Easy application by brush or sprayer
- Non hazardous and non toxic
- Non staining
- Does not interfere with concrete placements
- Can be used as mould release agent as well
Color
Milky White
Packaging
25 litre
200 litre
Antisol® E
An Emulsified Polyolefins based Concrete Curing Compounds.
Use
Antisol® E is sprayed onto newly laid concrete surfaces to form a thin film barrier against premature water loss. Without disturbance to the normal setting action, the concrete is the allowed to cure and achieve maximum properties. It is particularly useful in large areas of exposed concrete, such as:
- Highways
- Runways and taxiways
- Aprons and hard standings
- Roof decks
- Retaining walls
- Pre-stressed beams and piers
- Irrigation canals/channels
Characteristics and Advantages
- Ready to use and simple to apply
- Reduces incidence of plastic cracking
- Ensure achievement of desired strengths
- Minimises shrinkage
- Reduces dusting
- Increases frost resistance
- Alleviates other costly methods, such as hessian-watering
Color
White
Packaging
25 litre
200 litre
Antisol® S
A Soldium Silicate based Concrete Curing Compounds.
Use
Antisol® S is particularly recommended for the treatment of vertical surfaces which are to receive subsequent treatments where resin based curing membranes would be unsuitable because of their uncertain film breakdown, and the effect on the performance of further surface treatments
Characteristics and Advantages
- Clear, non staining and non toxic
- Helps concrete attain maximum hydration, strength, durability and surface hardness
- Becomes an integral part of the surface which assists long term curing and gives dust proofing properties
- Non flammable and suitable where solvent based systems are undersirable
- Shrinkage with associated hairline cracking and crazing greatly reduced in vertical and horizontal applications
- When used correctly will not prevent subsequent adhesion of concrete surface treatments and coatings
- Allows light foot traffic after 24 hours
Color
Transparence Blue
Packaging
25 litre
200 litre
Rugasol® F
Gel retarder for concrete surface specifically designed for the on-site production of exposed aggregate work or for producing a mechanical key to construction joints, stop ends, or subsequent rendering applications. Rugasol® F Provides an efficient, economical method of obtaining a rough bonding surface without the need for hacking,chipping or sand-blasting.
Use
Rugasol® -F have been specifically designed for the on-site production of exposed aggregate work or for producing a mechanical key to construction joints, stop ends, or subsequent rendering applications.
Characteristics and Advantages
- Is a Light brown paste which is ready for use from the container. It should be stirred before use and must not be diluted
- Surface retarder is used to expose aggregate on formed Portland Cement based concrete surfaces
- An efficient, economical method of obtaining a rough bonding surface without the need for hacking,chipping or sand-blasting
- Used to produce precast panels having a decorative architectural finish showing the colour and texture of natural aggregate. The aggregate remains whole and unbroken
- Painted directly on formwork for walls, ceilings, vertical construction joints or any similar formed concrete surface
- Dries on the formwork to a tough, but water-soluble film. Protect from rain. Forms may be coated before or after erection
Color
Light Brown
Packaging
20 kg
Rugasol® C
Liquid retarder for concrete surface specifically designed for the production between horizontal construction joint and surfaces to expose aggregate work. Rugasol® C eliminates the need for sandblasting, hacking and brush hammering,leaving the aggregate unbroken and firmly embedded.
Use
Rugasol® -C has been specifically designed for the production between horizontal construction joint and surfaces to expose aggregate work or for producing a mechanical key to construction joints, stop ends, or subsequent rendering applications
Characteristics and Advantages
- Is a transparent liquid that is ready to use straight from the container. It should not be diluted.
- An easy and economical method of obtaining a mechanical key for"kicker" joints, renderings and screeds on horizontal surfaces of freshly placed concrete
- eliminates the need for sandblasting, hacking and brush hammering,leaving the aggregate unbroken and firmly embedded
Color
Transparent
Packaging
20 kg
