Product Data Sheet Safety Data Sheet Show all documents

SikaGrout®-214-11 HF

High Performance Non-Shrink Grout for Large Volume

SikaGrout®-214-11 HF is a non-shrink, pourable cementitious grouting mortar with extended working time to suit local ambient temperatures.
SikaGrout®-214-11 HF does not contain materials which react with water to release hydrogen (HF: Hydrogen Free)

  • Excellent flowability
  • Good dimensional stability
  • High strengths, adjustable consistency
  • No bleeding
  • Non-toxic, non-corrosive
  • Ready and easy to use
  • Economical
  • Impact and vibration resistant
Contact Us
Product Data Sheet Safety Data Sheet Show all documents

Usage

  • Machine foundations
  • Rail beds
  • Columns in precast construction
  • Anchor bolts
  • Grouting in marine environment
  • Bridge bearings
  • Cavities, gaps, recesses,etc
 

Advantages

  • Excellent flowability
  • Good dimensional stability
  • High strengths, adjustable consistency
  • No bleeding
  • Non-toxic, non-corrosive
  • Ready and easy to use
  • Economical
  • Impact and vibration resistant

Packaging

25 kg/bag

Colour

Grey Powder

Product Details

Sustainability / Certifications / Approvals

APPROVALS / CERTIFICATES

Non-shrink definition as per ASTM C1107 applies.
Product Information

Shelf life

9 months from the date of production If stored properly in undamaged, original, sealed packaging

Storage conditions

Store in dry conditions and protected from direct sunlight.

Bulk Density

~1.47 kg/L
Technical Information

Compressive Strength

Water Content (14.5%)

Water Content (15%)

1 day

~400

~380

3 days~570~550
7 days~700~670

28 days

~800

~750

Note: Test at 28°C in lab condition. (kgf/cm2)

Bleeding

0

(ASTM C232)

Application

Application Information

Flowability

Water Content (%)

Consistency (J rote)

14.5

<15 seconds

15

<10 seconds

Note: Test at 28°C in lab condition.

Setting Time

Water Content (%)

Initial

Final

14.5

~ 4 : 00

~ 6 : 00

15

~ 4 : 15

~ 6 : 15

Note: Test at 28°C in lab condition. (hours : minutes)
Consumption

Consumption

Approx. 2 kg of powder for one litre of mortar.
For 1 m3 of mortar approx. 77 x 25 kg bags and 280 litres of water.
Application steps

MIXING

Powder should be added to the pre-gauged water to suit the desired consistency. For J rote of 15 seconds, approx. 3.625 litres of water. (approx. 14.5% by weight of SikaGrout®-214-11 HF) should be used. The amount of water may be reduced within the flowable consistency if desired.Mix mechanically with a low speed drill (max. 500 RPM) with a disc agitator attached, until a smooth, even consistency is achieved.

APPLICATION

Pour mortar after mixing. Ensure, that air entrapped into the grout is allowed to escape. When carrying out base plate grouting, ensure sufficient head of pressure is maintained to keep mortar flow uninterrupted. Make sure, that necessary formwork is firmly in place and watertight.

Grouting of Large Cavities

Depending on the volume to be filled, large aggregates, eg. 4-8 mm, 8-16 mm or 16-32 mm may be added to the SikaGrout® -214-11 HF at a ratio of between 50-100%. Round aggregates are more suitable than crushed. Vibrate to ensure good compaction.

 

Grouting of Machine Beds

Prewet thoroughly, no standing water in bolt holes. If possible, grout anchor bolts first, then the mortar bed in a second operation. Ensure continuous flow of mortar. Distance between anchor bolt and substrate to be at least 3 x max. diameter of mortar aggregates (approx. 10 mm.)

Grouting of Base Plates

Prewetting for approx. 24 hrs, no standing water. Maintain constant hydro-static pressure to ensure continuous flow. Use cable or chain to make sure that all cavities are filled. Make sure that entrapped air can escape.

CLEANING OF EQUIPMENT

Clean all tools and equipment with water immediately after use. Hardened mortar can only be removed mechanically.

Documents