Product Data Sheet Safety Data Sheet Show all documents

SikaLevel®-102 (TH)

POLYMER MODIFIED CEMENTITIOUS FLOOR LEVELLING COMPOUND FOR 2-15 MM

SikaLevel®-102 (TH) is a one part, polymer modified, self-leveling cementitious underlayment for the leveling and smoothing of interior floors.

  • Very good flow and cohesion of the fresh product
  • Easy to place by pump or manual application
  • Low shrinkage
  • For interior use
  • Good bond and compaction
  • Suitable for rolling chair traffic (from 3 mm thickness layer)
  • Good surface hardness and smoothness
  • Casein and Formaldehyde free
Product Data Sheet Safety Data Sheet Show all documents

Usage

SikaLevel®-102 (TH) can be applied to level floors at a thickness between 2 - 15 mm, prior to subsequent finishing. with ceramic or stone tiles, carpets, PVC sheets, suitable under wood and laminate floating floor systems. Typical uses are in residential and domestic properties.  

Advantages

  • Very good flow and cohesion of the fresh product
  • Easy to place by pump or manual application
  • Low shrinkage
  • For interior use
  • Good bond and compaction
  • Suitable for rolling chair traffic (from 3 mm thickness layer)
  • Good surface hardness and smoothness
  • Casein and Formaldehyde free

Packaging

25 kg per bag

Colour

Grey powder

Product Details

Product Information

Composition

Cement

Shelf life

6 months from the date of production

Storage conditions

Stored properly in original, unopened and undamaged sealed packaging in dry conditions

Maximum grain size

0.5 mm
System information

System structure

Priming:

  • Acrylic Primer: Sikafloor®-01 Primer (TH)
  • Synthetic Primers: Sikafloor®-161 HC, surface broadcated with sand grade 0.3–0.8 mm with minimal consumption 3 kg/m2

Primer selection depends on substrate and on layer thickness.

  • Cracks repairing: Sikadur®-31 CF Normal, surface broadcasted with sand grade 0.3–0.8 mm

Please refer to the relevant PDS and method statement before application.
Technical Information

Compressive strength

Time

Value

24 hours

> 10.0 N/mm2

7 days

> 15.0 N/mm2

26 days> 20.0 N/mm2

The values are valid at 25°C and 65% rel. humidity.

Tensile strength

28 days

> 5.0 N/mm2 (25°C)

 

Application

Application Information

Layer thickness

2-15 mm

Mixing ratio

5.75 - 6.0 L/25 kg

Pot Life

~ 20 min at 25°C

Waiting time to overcoating

Ready for foot traffic after approx. 3 hours

Applied product ready for use

Up to 3 mm after approx. 24 hours
Each additional mm further 24 hours. All values are approximate and are subject to climate fluctuation. Values given with +20 °C and 65 % rel. humidity, temperature of substrate minimum +15 °C.
Consumption

Consumption

1.5 kg/m2/mm

Yield

Thickness

Consumption

Yield/25 kg

2 mm

3 kg/m2

cca 8 m2

5 mm

7.5 kg/m2

cca 3 m2

10 mm

15 kg/m2

cca 1.7 m2

15 mm22.5 kg/m2cca 1.1 m2

Consumption is always depending on the substrate surface's roughness.
Application steps

MIXING

When mixing manually add the dry powder (25 kg) into a container with the clean water. The water required is between 5.75 and 6.0 liter per 25 kg bag of material. Mix thoroughly for a minimum of 2 minutes, stay for one minute and mix briefly. Use a low speed electric stirrer (max. 500 rpm).

If needed, use more than one mixer to ensure the continuous supply of freshly mixed product so that application is carried out without interruption. 

APPLICATION

  • After mixing pour out the levelling compound and spread using a smoothing trowel. Even surfaces are easily achieved with a suitable notched trowel.
  • In the case of higher layer-thickness, contact with vertical structures should be avoided by putting in a perimeter isolating strip.

CLEANING OF EQUIPMENT

Immediately after use clean tools with water.

 

Documents