SikaTop®-107 Seal TH
Two Component Cementitious Slurry for Waterproofing and Damp Poofing
SikaTop®-107 Seal TH is a two part polymer modified cementitious waterproofing mortar comprising of a liquid polymer and a cement based mix incorporating special admixtures. SikaTop®-107 Seal TH suitable for drinking water tank, wet room ,balcony and swimming pool.
- Easy to apply by brush, thin trowel and spray applications
- No water required
- Prebatched components
- Hand or spray applied
- Easy and fast mixing
- Very good adhesion
- Protects concrete against carbonation
- Protects against water penetration
- Approved for potable water contact
Usage
- Cementitious waterproofing for drinking and portable water tank, wet room , balcony and swimming pool system
- Waterproofing of basement walls in new construction and refurbishment
- Sealing fine “hairline” cracks in concrete structures (not subject to movement)
Advantages
- Easy to apply by brush, thin trowel and spray applications
- No water required
- Prebatched components
- Hand or spray applied
- Easy and fast mixing
- Very good adhesion
- Protects concrete against carbonation
- Protects against water penetration
- Approved for potable water contact
Packaging
25 kg/set | Part A | 4.55 kg / pail |
Part B | 20.45 kg / bag |
5 kg/set | Part A | 0.9 kg / pail |
Part B | 4.1 kg / bag |
Colour
Part A | White liquid |
Part B | Grey powder |
Mixed | Cement grey |
Product Details
SUSTAINABILITY
- LEED v4 and v4.1 BETA (ISO 16000, CDPH 01350 and ASTM D2369), Eurofins Product Testing A/S.
- WELL Building Standard TM (CDPH 01350 and ASTM D2369), Eurofins Product Testing A/S.
- Volatile organic compounds(VOC) content (ISO 11890-2:2013), Department of Science Service.
- Volatile and Non-Volatile matter (TIS 285:Part6-2016), Reference No. SPT 21.2/64.
APPROVALS / CERTIFICATES
Water quality test report from water quality control division, Provincial Water Works Authority of Thailand.
Composition
Part A | Liquid polymer and additive |
Part B | Portland cement selected aggregate and admixtures |
Shelf life
9 months (25 kg/set)
9 months (5 kg/set)
Storage conditions
Commencing from date of production if stored properly in undamaged and unopened original sealed packaging in dry and cool conditions.
Density
Fresh mortar density | ~ 2.00 kg/L | |
Dry density | ~ 1.4 kg / m3 | (TIS 1505 - 2541) |
Compressive strength
7 days | 20 MPa |
28 days | 30 MPa |
Tensile adhesion strength
0.7 MPa (Bond to concrete at 28 days) |
Water absorption
2.6% (at 28 days) | (ASTM C121-90 (Reapproved 1999)) |
Application
Mixing ratio
Used as slurry | A : B = 1 : 4 (parts by weight) |
Used as mortar | A : B = 1 : 4.5 (parts by weight) |
Layer thickness
For ordinary water conditions : A total thickness of 1.5 mm. at total consumption 3 kg/m2
For high water pressure conditions: A total thickness of 2 mm. at total consumption 4 kg/m2
Ambient air temperature
+8°C min. / +35°C max.
Substrate temperature
+8°C min. / +35°C max.
Pot Life
~ 30 minutes at +20°C
Waiting time to overcoating
Waiting time between coats.
10°C | ~ 12 hours |
20°C | ~ 6 hours |
30°C | ~ 3 hours |
If waiting time period exceeds 24 hours, lightly blastclean the surface. SikaTop®-107 Seal TH can be overpainted using solvent based primers or coatings. SikaTop®-107 Seal TH must cure for a minimum of 7 days before overcoating.
Consumption
- Dependent on the substrate roughness, surface profile and thickness of the layer applied.
- As a guide, ~ 2.0 kg / m2 / mm (excluding allowances for loss wastage,surface profile and porosity, etc.).
- 1 unit of 25 kg yields ~ 12.5 L of mortar.
MIXING
Mixing Time : ~ 3 minutes
Mixing Tools : SikaTop®-107 Seal TH must be mechanically mixed using a forced action mixer or in a clean drum using a drill and paddle (max. 500 rpm). A normal concrete free fall mixer is NOT suitable.
APPLICATION
Shake part A before using it. Pour approximately half of part A into the mixing container and add part B slowly while mixing. Add the remainder of part A and continue mixing until a uniform lump free consistency is achieved.The surface must be pre-wetted to a saturated surface dry condition before application.
As a slurry:
- Apply the mixed SikaTop®-107 Seal TH either mechanically by spray or by hand using a stiff brush. Applied in the same direction.
- Apply the 2nd coat of SikaTop®-107 Seal TH, applied by brush in crosswise direction to the first application as soon as first coat has hardened.
As a mortar:
- When SikaTop®-107 Seal TH is applied by trowel (e.g. for a smooth surface finish), the product must be mixed with a 10% reduction of part A (~ 1 A : 4.5 B).
- Apply the 2nd coat of SikaTop®-107 Seal TH as soon as the first coat has hardened. For pore / blowhole filling, tightly trowel into the pores / blowholes of the surface.
CURING TREATMENT
It is essential to cure SikaTop®-107 Seal TH immediately after application for a minimum of 3 to 5 days to ensure full cement hydration and to minimise cracking. Use polythene sheeting or similar approved methods.
CLEANING OF EQUIPMENT
Clean all tool and application equipment with clean water immediately after use. Hardened / cured material can only be removed mechanically.
VDO
For this content to be displayed, you need to accept all cookies in the cookie settings and confirm your selection or by clicking the “Allow All” button.
For this content to be displayed, you need to accept all cookies in the cookie settings and confirm your selection or by clicking the “Allow All” button.