Product Data Sheet Show all documents
SikaTile®-310 Lite

SikaTile®-310 Lite

CEMENT BASED TILE ADHESIVE FOR CERAMIC AND CLAY TILE

SikaTile®-310 Lite is a general cement-based tile adhesive for ceramic and clay tile with a single component, pre-packed tiling adhesive mortar combining cement with selected grades of sand and several admixtures. It only requires the addition of water.

  • Good bonding strength
  • Adhesion is better than black cement.
  • Good value tile adhesive to replace traditional
    mortar
  • Easy to use
  • No need for pre-soaking tiles
Product Data Sheet Show all documents

Usage

  • Suitable for fixing ceramic tile up to 40 x 40 cm.
  • Exterior and Interior Floor
  • Interior wall
  • Substrates: Cement  

Advantages

  • Good bonding strength
  • Adhesion is better than black cement.
  • Good value tile adhesive to replace traditional
    mortar
  • Easy to use
  • No need for pre-soaking tiles

Packaging

20 kg/ bag

Colour

Grey powder

Product Details

Product Information

Composition

Hydraulic binder, mineral filler and admixtures

Shelf life

12 months from date of production if stored in undamaged and unopened, original sealed packaging

Storage conditions

Store in dry condition and protected from direct sunshine

Density

1.2 ± 0.1 kg/L

pH-Value

12 ± 1
Technical Information

Tensile adhesion strength

Initial ≥ 0.5 MPa

 

Application

Application Information

Ambient air temperature

+5°C to +35°C

Mixing ratio

Approximate 4.5 to 5 litre water per bag 20 kg

Pot Life

180 - 240 minutes (at 25°C)

Open Time

10 - 15 minutes (at 25°C)

Adjustability time

10 - 15 minutes (at 25°C)

Applied product ready for use

~ 24 hours
Consumption

Consumption

Trowel Size

Tile Size

(cm x cm)

Tile Surface

(cm2)

Consumption

(20 kg)

3 mm

2.5 x 2.5

5 x 5

6.25

25

7 - 8 m2

6 mm

10 x 10

20 x 20

20 x 25

30 x 30

100

400

500

900

5 - 6 m2

9 mm

40 x 40

1,600

2 - 3 m2

Note : 

1. This is an average calculation. Actual usage may differ from the estimate. Due to the different surface conditions. Surface absorption and the purpose of the individual's use.

2. For tile sizes larger than 40x40 cm, apply tile adhesive on the surface and a very thin layer on the back of the tile.
Application steps

MIXING

  • Mix SikaTile®-310 Lite 20 kg with 4.5 - 5 Litres of clean water with an electrical mixer until the compound is evenly distributed.
  • Allow the mixture to stand for 2 - 3 minutes for a good reaction and reduce air bubbles before using the adhesive. 

APPLICATION

  • Spread tile adhesive by using a notched trowel onto the substrate.
  • Fix tile on tile adhesive and knock it over with a rubber hammer.
  • Dual bonding should be applied when the tile size is larger than 25 cm x 25 cm. Apply a thin layer of tile adhesive onto the back of the tile, then fix the tile onto the adhesive substrate.  

  • Once the tiles have been laid, leave them to stand for 24 hours or until the tile adhesive is dry before grouting with SikaTile Tile Grout.  

Documents

Consumption Calculator

Remark:

  • This calculator was developed base on SikaTile tile grout and tile adhesive specification.
  • The result are average and vary, depend on job site condition. Please contact Sika’s Sales Representative for specific consultant.

Recommended trowel size:

  • Trowel size 3 mm, suitable for tile size <10x10 cm.
  • Trowel size 6 mm, suitable for tile size between 10x10 to 30x30 cm.
  • Trowel size 9 mm, suitable for tile size >30x30 cm.