Product Data Sheet Safety Data Sheet Show all documents

DAVCO® TTB PLUS

PREPACKED CEMENTITIOUS TILE ADHESIVE

DAVCO® TTB PLUS is a general cement-based tile adhesive for ceramic and clay tile with a single component, pre-packed tiling adhesive mortar combining cement with selected grades of sand and several admixtures. Only requires the addition of water.

  • Laying ceramic tiles, granito tiles up to 60x60 cm on both floor and wall
  • Good bonding strength.
  • Extended open time resulting in faster application
  • Tile can be adjusted after laying within 15 minutes
  • Smooth and easy to use
  • Low VOCs
Where to buy Consumption Calculator
Product Data Sheet Safety Data Sheet Show all documents

Usage

  • Perfect for ceramic floor and wall tiles. Interior and exterior use.
  • Suitable for granito interior floor and wall installation
  • Can be used for granito exterior floor installation only
  • Substrates: Cement  

Advantages

  • Laying ceramic tiles, granito tiles up to 60x60 cm on both floor and wall
  • Good bonding strength.
  • Extended open time resulting in faster application
  • Tile can be adjusted after laying within 15 minutes
  • Smooth and easy to use
  • Low VOCs

Packaging

20 kg/ bag

Colour

Grey powder

Product Details

Sustainability / Certifications / Approvals

APPROVALS / CERTIFICATES

  • ANSI 118.1
Product Information

Composition

Hydraulic binder, mineral filler, polymer and admixtures

Shelf life

12 months from date of production if stored in undamaged and unopened, original sealed packaging.

Storage conditions

Store in dry condition and protected from direct sunshine.

Density

1.4 ± 0.1 kg/L

pH-Value

12 ± 1
Technical Information

Tensile adhesion strength

Initial  ≥ 0.5 MPa

Application

Application Information

Mixing ratio

Approx. 4.8 to 5.4 litre water per bag 20 kg

Ambient air temperature

+5°C to +35°C

Pot Life

180 - 240 minutes (at 25°C)

Open Time

20 - 25 minutes (at 25°C)

Adjustability time

15 - 20 minutes (at 25°C)

Applied product ready for use

~ 24 hours
Consumption

Consumption

Trowel size

Size of tile
(cm x cm)

Surface of tile
(cm2)

Consumption
(20 kg)

3 mm

2.5 x 2.5
5.0 x 5.0

6.25
25

7 - 8 m2

6 mm

10 x 10
20 x 20
20 x 25
30 x 30

100
400
500
900		5 - 6 m2
9 mm40 x 40
50 x 50
60 x 60
> 60 x 60		1600
2500
3600
> 3600		2 - 3 m2

Note:
1. This is an average calculation. Actual usage may differ from the estimate. Due to the different surface conditions. Surface absorption and the purpose of the individual's use.
2. For tile size more than 40 cm x 40 cm should apply tile adhesive on the surface and a very thin layer on the back of tile.
Application steps

MIXING

  • Mix DAVCO® TTB PLUS 20 kg with 4.8 - 5.4 Litres of clean water by electrical mixer until the compound is evenly distributed.
  • Allow the mixture to stand for 2 - 3 minutes for good reaction and reducing air bubble before using the adhesive.

APPLICATION

  • Spread tile adhesive by using notched trowel onto substrate.
  • Fix tile on tile adhesive and knocked over with rubber hammer.
  • The dual bonding will be applied when size of tile is over than 25 cm x 25 cm. Applying thin layer of tile adhesive onto a back of tile, then fix the tile on tile adhesive substrate.
  • Once the tiles have been laid, leave to stand for 24 hours or the tile adhesive is dry before grouting with DAVCO Tile Grout.
 

Documents