Product Data Sheet Show all documents
SikaTile®-350 Performance

SikaTile®-350 Performance

QUALITY TILE ADHESIVE FOR PORCELAIN AND GRANITO TILE

SikaTile®-350 Performance is a standard cement-based tile adhesive with polymer-modified as a single component, pre-packed tiling adhesive mortar combining cement with selected grades of sand and several additives. Only requires the addition of water.

  • Dedicated to granito and low porous tiles
  • Excellent bonding strength
  • Extended open time resulting in faster application
  • Tile can be adjusted after laying within 15 minutes
  • Smooth and easy use
SikaTile®-350 Performance
Where to buy
Product Data Sheet Show all documents

Usage

  • Perfect for granito tiles up to 90x90 cm on interior floor and wall installation.
  • Can be used for large-sized granito tile for exterior floor installation only.
  • General ceramic tile. Both interior and exterior floor and wall installation.
  • Substrates: Cement. It is also suitable for tiling onto waterproof membranes in wet areas.  

Advantages

  • Dedicated to granito and low porous tiles
  • Excellent bonding strength
  • Extended open time resulting in faster application
  • Tile can be adjusted after laying within 15 minutes
  • Smooth and easy use

Packaging

20kg/ bag

Colour

Grey powder

Product Details

Sustainability / Certifications / Approvals

SUSTAINABILITY

  • LEED v4 and v4.1 BETA
  • WELL Building StandardTM

CERTIFICATES AND TEST REPORTS

  • EN 12004 C1TE
  • ANSI 118.1
  • TIS 2703-2559
Product Information

Composition

Hydraulic binder, mineral filler, polymer, and admixtures

Shelf life

12 months from date of production if stored in undamaged and unopened, original sealed packaging

Storage conditions

Store in dry condition and protected from direct sunshine

Density

1.3 ± 0.1 kg/L

pH-Value

12 ± 1
Technical Information

Tensile adhesion strength

At 28 days

Initial

≥ 0.5 MPa

Water immersion

≥ 0.5 MPa

Heat aging≥ 0.5 MPa
Open time bonding after 20 min≥ 0.5 MPa
Extended open time after not less than 30min≥ 0.5 MPa

Shear adhesion strength

Glazed Wall Tile

7 days

≥ 1.38 MPa

7 days water immersion

≥ 1.03 MPa

Porcelain Mosaic Tile

1 day

≥ 0.34 MPa

7 days

≥ 1.03 MPa
7 days water immersion≥ 0.69 MPa
28 days≥ 1.03 MPa

Application

Application Information

Slip resistance

≤ 0.5 mm

Ambient air temperature

+5°C to +35°C

Mixing ratio

Approximate 4.8 to 5.6 litre water per bag 20 kg

Pot Life

180 - 240 minutes (at 25°C)

Open Time

20 - 25 minutes (at 25°C)

Adjustability time

15 - 20 minutes (at 25°C)

Applied product ready for use

~ 24 hours
Consumption

Consumption

Trowel Size

Tile Size

(cm x cm)

Tile Surface

(cm2)

Consumption

(20 kg)

3 mm

2.5 x 2.5

5 x 5

6.25

25

7 - 8 m2

6 mm

10 x 10

20 x 20

20 x 25

30 x 30

100

400

500

900

5 - 6 m2

9 mm

40 x 40

50 x 50

60 x 60

>60 x 60

1,600

2,500

3,600

>3,600

2 - 3 m2

Note : 

1. This is an average calculation. Actual usage may differ from the estimate. Due to the different surface conditions. Surface absorption and the purpose of the individual's use.

2. For tile sizes larger than 40x40 cm, apply tile adhesive on the surface and a very thin layer on the back of the tile.
Application steps

MIXING

  • Mix SikaTile®-350 Performance 20 kg with 4.8 - 5.6 Litres of clean water with an electrical mixer until the compound is evenly distributed.
  • Allow the mixture to stand for 2 - 3 minutes for a good reaction and reduce air bubbles before using the adhesive.

APPLICATION

  • Spread tile adhesive by using a notched trowel onto the substrate.
  • Fix tile on tile adhesive and knock it over with a rubber hammer.
  • Dual bonding should be applied when the tile size is larger than 25 cm x 25 cm. Apply a thin layer of tile adhesive onto the back of the tile, then fix the tile onto the adhesive substrate.
  • Once the tiles have been laid, leave them to stand for 24 hours or until the tile adhesive is dry before grouting with SikaTile Tile Grout.   

Documents